Ever looked at your factory layout in Arknights: Endfield and thought, “If I could fit just one more Depot Gate, this entire line would be perfect”?
Good news: you actually can.
Players have discovered a Depot Gate edge placement trick that lets you place Depot Gates so they stick out over the factory edge, effectively giving you extra space in tight layouts. It even works on both sides in some setups, which means you can squeeze more efficiency out of the same factory footprint without unlocking new zones or restructuring everything.
This trick has quickly gained attention among players who enjoy factory optimization and min-maxing production lines, especially when space becomes the main bottleneck. While it isn’t an officially explained mechanic, it currently works within the game’s placement rules and can be a game-changer for compact layouts.
Here’s exactly how to place a Depot Gate over the edge in Endfield, why it works, and whether it’s safe to rely on.
Can You Place a Depot Gate Over the Edge in Endfield?
Yes. In Arknights: Endfield, you can place a Depot Gate so that it partially hangs over the edge of the factory build area. By taking advantage of a small placement quirk in the factory build system, Depot Gates are able to overhang the factory boundary while still functioning as normal, allowing items to pass through without immediately breaking production.
This is not an officially documented feature and is better described as a factory edge placement exploit or trick rather than an intended mechanic. However, as of now, it works reliably enough that many players are actively using it in optimized factory layouts, especially when space is tight and every extra gate matters.
While it’s effective, players should keep in mind that exploits like this may be adjusted or patched in future updates, so it’s best used with some caution.
How to Place a Depot Gate Over the Factory Edge
This Depot Gate clipping trick doesn’t require upgrades, research, or special tech — it’s all about careful placement and a bit of patience. You’re essentially nudging the game’s placement rules right up to their limit.
Here’s how to do it:
- Go to the edge of your factory build area where space is tight.
- Open the build menu and select Depot Gate in Arknights: Endfield.
- Rotate the gate so it’s facing outward toward the factory boundary. Orientation matters here.
- Slowly move the gate toward the factory edge until the placement preview starts to partially hang over the boundary line.
- If the game allows placement, confirm it immediately.
- In some layouts, you can repeat this on the opposite side of the factory edge to squeeze in one more gate.
Small adjustments make a big difference. If the gate won’t place, try rotating it again or shifting it by a tiny amount — sometimes just a single grid nudge is enough to make the placement valid.
Why the Depot Gate Edge Placement Works
In Arknights: Endfield, the factory system treats placement validation and visual model rendering as two separate checks. The game first decides whether a building is allowed based on its core placement tile, not the full visual footprint of the model.
As long as that main placement tile is considered valid, the game may allow the structure to be placed — even if part of the Depot Gate model clips outside the factory grid. This small mismatch between collision rules and visual rendering is exactly what makes this Endfield factory edge exploit possible, letting players squeeze extra utility out of tight factory layouts without breaking the build rules outright.
Does the Over-Edge Depot Gate Actually Work?
In most cases, yes — an over-edge Depot Gate functions just like a normally placed one in Arknights: Endfield.
When placed correctly:
- Items pass through normally without getting stuck
- Production lines recognize the gate as a valid output point
- Overall output behavior remains unchanged, with no immediate loss in efficiency
That said, because this setup relies on a placement trick rather than an intended mechanic, results can vary. Tighter or more complex factory layouts may occasionally run into minor pathing or flow issues, especially when multiple machines are feeding into the same area. It usually works well, but it’s still something you’ll want to test before fully committing a critical production line to it.
Risks and Things to Watch Out For
Before fully committing to this Depot Gate placement bug in Arknights: Endfield, there are a few important things you should keep in mind.
- Pathing issues: In tighter factory layouts, items may briefly clog, slow down, or take awkward routes through the over-edge gate.
- No storage bonus: This trick only gives you an extra gate, not additional depot storage or higher capacity limits.
- Patch risk: Since this is an exploit-style placement trick, future updates could change or remove it entirely.
- Blueprint safety: Always save a blueprint once you successfully place the gate, so you can quickly restore the layout if something breaks.
If your production line starts behaving strangely or efficiency drops, the safest move is to remove the over-edge gate and revert to a standard placement.
When This Trick Is Worth Using
This Endfield factory layout optimization trick is best used in specific situations where squeezing out extra efficiency really matters.
Use it if:
- You’re short on factory space and need just one more output gate to complete a production line
- You’re optimizing ratios and throughput and don’t want to redesign the entire layout
- You’re comfortable accepting minor risk in exchange for better efficiency in Arknights: Endfield
Avoid it if:
- The production line is mission-critical and needs to run without interruption
- You want a fully future-proof factory that won’t be affected by potential placement fixes or patches
Used wisely, this trick can be a smart workaround — just make sure it fits your risk tolerance and factory goals.
Safer Alternatives to Over-Edge Placement
If you’d rather not rely on a Depot Gate clipping trick in Arknights: Endfield, there are a few safer and more stable options to consider instead.
- Rebalance machine ratios to reduce the number of output gates your production line needs
- Spread outputs across multiple factory zones to avoid congestion in a single area
- Expand depot infrastructure rather than forcing extra gates into an already tight layout
These approaches may not be as flashy as over-edge placement, but they’re far more reliable long-term and won’t risk breaking if the factory placement rules change in a future update.
Final Verdict
Yes — you can place Depot Gates over the edge in Arknights: Endfield, and right now, it works.
It’s a clever way to squeeze extra efficiency out of compact factory layouts, especially when space is the main thing holding your production back. Just don’t build your entire production chain around this trick unless you’re prepared for possible fixes or changes in future patches.
The factory must grow… sometimes it just has to grow a little creatively.
Read more